Speak the language.
232 terms you will hear on every project call, defined without the jargon.
2N
A redundancy design with two fully independent systems, each able to carry the entire load alone. Either can fail or be serviced without affecting the load.
2N+1
A 2N design with an added spare component, so redundancy remains even while one side is down for maintenance and a component has also failed.
Actuator
The motor or air operator that moves a valve or damper when a controller sends a signal.
Additionality
The idea that a clean energy purchase causes new renewable generation to be built that would not have existed otherwise.
Adiabatic Cooling
Cooling that uses the evaporation of water into air to lower air temperature before it passes over a coil or into a space.
Affinity Laws
Rules that link pump or fan speed to flow, pressure and power. Power falls with the cube of speed, which is why slowing a pump saves so much.
Approach Temperature
The difference between the water temperature leaving a cooling tower and the ambient wet bulb temperature. A smaller approach means a more capable tower.
Approved Manufacturer List (AML)
A list kept by an owner or designer of manufacturers whose products may be used on a project. Getting onto it is often required before a product can be bid.
Arc Flash
A dangerous release of energy caused by an electrical fault through the air. It produces intense heat, light and pressure.
As-built
Drawings and records updated at project end to show what was actually installed, including field changes from the original design.
ASHRAE
The American Society of Heating, Refrigerating and Air-Conditioning Engineers. It publishes widely used thermal guidelines and design standards for data center environments.
Automatic Transfer Switch (ATS)
A switch that moves a load from one power source to another, usually from utility to generator, without operator action when the primary source fails.
Availability Zone
An isolated location within a cloud region with its own power, cooling and networking. Zones in a region are linked by fast connections so workloads can survive the loss of one.
Balancing Valve
A valve used to set and adjust flow in a branch of a hydronic system so each branch gets the right amount.
Bandwidth
The maximum amount of data a network connection can carry in a given time.
Basis of Design
The documented set of criteria, assumptions and named products a design is built on. Naming a manufacturer here strongly shapes what is bid and installed.
Battery Energy Storage System (BESS)
A set of batteries and controls that stores electricity and releases it when needed, for backup or grid support.
Behind-the-Meter
Generation or storage located on the customer side of the utility meter. It serves the site directly without passing through the utility grid.
Blowdown
Water intentionally drained from a cooling tower or boiler to remove built-up minerals and solids.
Border Gateway Protocol (BGP)
The routing protocol networks use to share which address ranges they can reach, forming the basis of internet routing.
Build-to-Suit
A facility designed and built to a specific tenant's requirements, often under a long-term lease.
Building Information Modeling (BIM)
A shared 3D digital model of a building that carries design, coordination and equipment data.
Building Management System (BMS)
A control system that monitors and runs building equipment such as chillers, pumps, fans and valves.
Busway
An enclosed system of metal bus bars that distributes power along a run, with tap-off points for connecting loads. It is an alternative to cable and conduit.
Butterfly Valve
A quarter-turn valve with a rotating disc in the pipe, widely used to isolate or throttle water in large cooling systems.
Bypass
A path that routes power or fluid around a component so it can be serviced or so a failure does not stop the system.
Cage
A fenced or caged area inside a shared data hall that holds one customer's equipment and limits physical access.
Capacity Factor
The actual energy a power plant produces over a period divided by what it would produce running at full output the whole time.
Capacity Planning
The process of forecasting power, cooling, space and network needs so supply is ready before demand arrives.
Carbon Usage Effectiveness (CUE)
A metric of carbon dioxide emitted per unit of IT energy used. It is total facility emissions divided by IT equipment energy.
Carrier-Neutral
Describes a facility that lets many network providers connect, rather than tying tenants to one carrier.
Change Control
A formal process for requesting, reviewing, approving and recording changes to a live facility to reduce the risk of outages.
Change Order
A written change to the scope, price or schedule of a construction contract after it is signed.
Check Valve
A valve that lets fluid flow in one direction only and closes to stop reverse flow.
Chilled Water
Water cooled by a chiller and circulated to air handlers or heat exchangers to remove heat from the data hall.
Chiller
A machine that removes heat from water using a refrigeration cycle, producing chilled water for cooling systems.
Clash Detection
A model-based check that finds places where different trades' designs, such as pipes and cable trays, occupy the same space.
Closed-Loop Cooling
A cooling system that recirculates the same fluid in a sealed circuit, using little or no makeup water.
Cloud Region
A geographic area where a cloud provider operates a group of data centers, usually organized into several availability zones.
Co-Location (Colo)
A service where a customer places its own IT equipment in a provider's facility and rents space, power, cooling and connectivity.
Cold Aisle
The aisle between server rows where cool supply air is delivered to the fronts of equipment.
Commissioning (Cx)
A structured process of testing and documenting that systems are installed and perform as designed before the facility goes live.
Computational Fluid Dynamics (CFD)
A simulation method used to predict airflow and temperature in a data hall.
Computer Room Air Conditioner (CRAC)
A cooling unit that uses a built-in refrigerant compressor to cool and move air in the data hall.
Computer Room Air Handler (CRAH)
A cooling unit that uses chilled water from a central plant, with fans moving air across a water coil.
Concurrent Maintainability
The ability to service or replace any capacity component or distribution path without shutting down the IT load.
Condenser Water
Water that carries heat from chillers to a cooling tower, where the heat is released to the atmosphere.
Conditional Use Permit
A local approval that allows a use not automatically permitted in a zone, subject to conditions.
Construction Manager (CM)
The party that manages a project's schedule, cost and quality on the owner's behalf, sometimes also holding trade contracts.
Containment
Physical barriers such as panels, doors or curtains that separate hot and cold air streams so they do not mix.
Content Delivery Network (CDN)
A distributed set of servers that store copies of content near users to speed delivery.
Contractor Furnished Equipment (CFE)
Equipment bought and supplied by the contractor as part of the construction contract.
Control Valve
A valve that adjusts flow in response to a signal from a controller to regulate temperature, pressure or flow.
Cooling Distribution Unit (CDU)
A unit that circulates liquid coolant between the facility water loop and the server cooling loop, controlling temperature, flow and pressure.
Cooling Tower
A structure that rejects heat to the atmosphere, mainly by evaporating a small part of the circulating water.
Critical Path
The longest chain of dependent tasks in a schedule. A delay to any task on it delays the whole project.
Cross-Connect
A direct physical cable link between two customers or between a customer and a carrier within the same facility.
Cycles of Concentration
How many times the minerals in cooling tower water are concentrated compared with the incoming water. More cycles means less blowdown and less makeup water.
Dark Fiber
Installed optical fiber that is not lit by a provider. A customer leases it and supplies its own equipment to use it.
Data Center Infrastructure Management (DCIM)
Software that collects and displays data on power, cooling, space and assets so operators can monitor and plan a facility.
Data Hall
A room within a data center that holds racks of IT equipment and the systems that serve them.
Delta T
The temperature difference between supply and return, such as chilled water leaving and entering a cooling coil. A larger delta T moves more heat per unit of flow.
Demand Charge
A utility fee based on the highest power draw during a billing period, not total energy used. It is billed per kW of peak demand.
Demand Response
A program where a customer reduces or shifts power use on request in return for payment or lower rates.
Dew Point
The temperature at which air becomes saturated and moisture begins to condense. It is a key limit for chilled surfaces in a data hall.
Differential Pressure
The difference in pressure between two points in a system. It is often used to control pump speed or confirm filter and strainer condition.
Digital Twin
A live virtual model of a facility that is fed with real operating data and used to monitor, test and plan changes.
Direct-to-Chip Cooling
A liquid cooling method where cold plates attached to processors carry heat away in circulating liquid.
Diverse Path
A network or utility route that follows a physically separate course from another so one event does not cut both.
Drift
Tiny droplets carried out of a cooling tower by the air stream. Drift eliminators reduce it.
Dry Bulb Temperature
The ordinary air temperature measured by a standard thermometer, without accounting for moisture.
Dry Cooler
A heat rejection device that cools a fluid with outdoor air passing over coils, without evaporating water.
Dual Corded
Describes equipment with two power supplies that can be fed from separate power paths for redundancy.
Due Diligence
The investigation a buyer or investor performs on a property or company before closing a deal.
Easement
A legal right to use part of someone else's land for a defined purpose, such as a utility line or access road.
Economizer
A system that uses cool outdoor air or water to reduce or replace mechanical cooling when conditions allow.
Edge Computing
Processing data close to where it is created or used instead of in a distant central facility.
Edge Data Center
A smaller facility placed close to users or devices to reduce latency and local network load.
Electrical Power Monitoring System (EPMS)
A system that monitors electrical equipment such as switchgear, breakers and meters, and reports status, loads and alarms.
Emergency Operating Procedure (EOP)
A written set of steps for responding to a specific failure or emergency, such as a power loss or cooling failure.
Energy Reuse Effectiveness (ERE)
A metric like PUE that credits energy reused outside the data center, such as waste heat sent to a nearby building.
Engineering, Procurement and Construction (EPC)
A contract model where one firm handles design, purchasing and building, and delivers a finished facility.
Entitlement
The process of getting government approvals to develop land for a specific use, including zoning, permits and site plan approval.
Escrow
An arrangement where a neutral third party holds money or documents until the conditions of a deal are met.
Facility Water System
The loop that carries heat from coolant distribution units to the outdoor heat rejection equipment.
Fail Position
The position a valve or damper moves to if power or the control signal is lost, such as open, closed or stay as is.
Fault Tolerance
A design that keeps running through a failure without operator action.
Fault Tolerant
Describes a design that keeps running through a single failure, including during planned maintenance.
Fiber Optic Cable
A cable that carries data as pulses of light through glass strands, supporting long distances and high speeds.
Flow Rate
The volume of fluid moving through a pipe over time, often stated in gallons per minute.
Flushing
Pushing water through new piping at high speed to remove debris before equipment is connected.
Flywheel
A spinning mass that stores energy as motion and releases it as electricity. It can bridge the gap between a power loss and generator start.
Free Cooling
Cooling that uses outdoor air or water at low temperatures instead of running compressors.
Front-of-the-Meter
Generation or storage connected on the utility side of the meter. Its output flows onto the grid and is sold or delivered through the utility.
Fuel Day Tank
A smaller fuel tank near a generator that feeds it directly, refilled from larger bulk storage.
General Contractor (GC)
The firm responsible for building a project under contract, managing subcontractors, schedule and site work.
Generator
An engine-driven electrical machine that supplies backup power when utility power is lost.
Geotechnical Investigation
Soil and rock testing at a site to determine bearing strength, groundwater and foundation design needs.
Glycol
A fluid mixed with water to lower its freezing point in cooling loops exposed to cold weather.
Gray Space
The areas that house supporting infrastructure such as power and cooling equipment, rather than IT racks.
Guaranteed Maximum Price (GMP)
A contract type where the owner pays actual costs up to a capped total, with the contractor bearing costs above the cap.
Harmonics
Distorted electrical waveforms at multiples of the base frequency, often created by electronic loads. They can cause heating and reduce power quality.
Heat Exchanger
A device that transfers heat from one fluid to another without letting them mix.
High-Performance Computing (HPC)
The use of tightly connected, powerful computers to solve demanding calculations. These systems often have high rack density.
Hot Aisle
The aisle behind server rows where heated exhaust air is collected and returned to cooling equipment.
HVAC
Heating, ventilation and air conditioning. In a data center it mainly means the systems that remove heat from IT equipment.
Hydronic
Describes heating or cooling systems that move heat using water or other liquids in pipes.
Hyperscale
Describes very large facilities and operators that deploy compute at massive scale, usually run by large cloud and internet companies.
Immersion Cooling
A method that submerges IT equipment in a non-conductive liquid that absorbs heat directly from the components.
Integrated Systems Test (IST)
A final commissioning test that exercises all systems together, often by simulating utility loss and failures, to prove they work as one.
Interconnection
A physical or virtual link between networks or between a customer and a service, often provided within a data center.
Interconnection Queue
The process a utility or grid operator uses to study and sequence requests to connect new load or generation.
Internet Exchange (IX)
A facility or network where many providers connect to exchange traffic directly with one another.
Internet Service Provider (ISP)
A company that provides customers with access to the internet.
ISO 27001
An international standard for information security management systems. Certification shows an organization manages security risks in a defined way.
Isolation Valve
A valve used to shut off part of a piping system so equipment can be serviced while the rest keeps running.
Jitter
Variation in the delay of data packets arriving over a network. High jitter harms voice, video and real-time applications.
kVA
Kilovolt-amperes, a unit of apparent power equal to volts times amps divided by 1,000. It includes both useful and non-useful current.
kW
Kilowatt, a unit of real power equal to 1,000 watts. It is the usual measure of IT load and rack density.
Latency
The delay for data to travel from one point to another, usually measured in milliseconds.
Leadership in Energy and Environmental Design (LEED)
A green building rating program that scores projects on energy, water, materials and site practices.
Leak Detection Cable
A sensing cable laid under pipes or floors that raises an alarm when it touches liquid.
Letter of Intent (LOI)
A non-binding document outlining the main terms of a proposed deal before a final contract is signed.
Level 1 Commissioning (L1)
The factory stage of commissioning, covering witness testing and acceptance of equipment at the manufacturer.
Level 2 Commissioning (L2)
Checks that equipment is delivered and installed correctly, including inspection of placement, connections and labeling.
Level 3 Commissioning (L3)
Start-up and functional testing of individual pieces of equipment to confirm each operates as specified.
Level 4 Commissioning (L4)
Tests that systems work together, such as power and cooling chains, under load and during failure scenarios.
Level 5 Commissioning (L5)
Integrated systems testing of the whole facility, including how power, cooling, controls and the operations team respond to failures.
Liquidated Damages
A pre-agreed payment a contractor owes if it misses a deadline or performance target in the contract.
Load Bank
A device that creates an artificial electrical or heat load so power and cooling systems can be tested without live IT equipment.
Load Factor
The ratio of average power use to peak power use over a period. A high load factor means a site draws power steadily.
Load Letter
A written statement from a utility describing the power it will serve to a site and on what timeline.
Long-Lead
Describes equipment with long manufacturing and delivery times, such as generators, switchgear and chillers, which must be ordered early.
Maintenance Bypass
A switch path that lets a UPS or other device be isolated for service while the load stays powered from another source.
Maintenance Operating Procedure (MOP)
A detailed written procedure for carrying out maintenance on a specific system, including steps, approvals and rollback.
Makeup Water
Water added to a cooling system to replace what is lost to evaporation, blowdown or leaks.
Mean Time Between Failures (MTBF)
The average operating time between failures of a repairable system. A higher value suggests better reliability.
Mean Time to Repair (MTTR)
The average time needed to restore a failed system to service.
Mechanical, Electrical and Plumbing (MEP)
The building systems for cooling, power distribution and water or piping, and also the trades and engineers who design and install them.
Medium Voltage
Electrical distribution above low voltage and below high voltage, commonly used to bring power into a large data center site.
Meet-Me Room (MMR)
A secure room where carriers and customers connect their networks to each other through cross-connects.
Microgrid
A local electrical system with its own generation and controls that can run on its own or connect to the main grid.
Modular Construction
Building with factory-made sections or skids that are shipped to the site and connected, which can shorten the schedule.
MW
Megawatt, equal to 1,000 kilowatts. Data center capacity is commonly stated in megawatts.
N
The number of components needed to carry the full load with no spare. A system built at N has no redundancy.
N+1
A design with one extra component beyond what the load needs, so a single failure does not cause an outage.
Network Operations Center (NOC)
A staffed location that monitors network and facility health and coordinates responses to incidents.
NFPA
The National Fire Protection Association. It publishes fire and electrical safety codes and standards, including those used in data centers.
Notice to Proceed (NTP)
A formal instruction from the owner that lets a contractor begin work or a stage of work.
One-Line Diagram
A simplified drawing that shows an electrical system as single lines between major components such as utility feeds, switchgear, transformers and loads.
Option Agreement
A contract that gives a buyer the exclusive right to purchase land at set terms within a set time, for a fee.
Owner Furnished Equipment (OFE)
Equipment bought by the owner and given to the contractor to install.
Owner's Representative
A person or firm hired by the owner to manage a project and protect the owner's interests during design and construction.
Pad-Mounted Transformer
A weather-protected transformer on a concrete pad outdoors, used to step down utility voltage for a site.
Payment in Lieu of Taxes (PILOT)
An agreed payment to a local government in place of regular property taxes, often used with tax-exempt or incentive-backed projects.
Peak Shaving
Reducing power taken from the grid during peak demand periods by using stored or on-site energy.
Peering
An arrangement where networks exchange traffic directly with each other, often without paying for transit.
Phase I Environmental Site Assessment
A review of a property's history and records to identify possible contamination before purchase.
Power Distribution Unit (PDU)
Equipment that distributes electrical power to racks or IT equipment, sometimes with monitoring or a built-in transformer.
Power Factor
The ratio of real power (kW) to apparent power (kVA). A value near 1 means power is used efficiently.
Power Purchase Agreement (PPA)
A long-term contract to buy electricity from a specific generator at agreed terms.
Power Usage Effectiveness (PUE)
Total facility energy divided by IT equipment energy. A value closer to 1 means less energy goes to overhead like cooling.
Powered Shell
A building delivered with the structure, utility power and basic site work in place, leaving the tenant to complete the interior fit-out.
Precision Cooling
Cooling equipment designed for the steady temperature and humidity control that IT equipment needs.
Prefabrication
Assembling components such as piping, electrical rooms or racks off site before delivery to the project.
Pump Curve
A graph that shows how much flow a pump delivers at different pressure levels. It is used to pick and check pump selection.
Punch List
A list of minor items that remain to be fixed or completed before a project is accepted as finished.
Rack
A standardized frame that holds servers, switches and other IT equipment, usually 19 inches wide.
Rack Density
The amount of power drawn per rack, usually stated in kilowatts per rack.
Raised Floor
A floor lifted above the structural slab on supports, creating a space below for cabling or cool air delivery.
Rear-Door Heat Exchanger
A water-cooled coil mounted on the back of a rack that cools exhaust air as it leaves the rack.
Recovery Point Objective (RPO)
The maximum amount of data loss, measured in time, that an organization will accept after a disruption.
Recovery Time Objective (RTO)
The target time to restore a service after a disruption.
Redundancy
Extra components or paths provided so that a failure does not interrupt service.
Relative Humidity
The amount of moisture in air compared with the most it can hold at that temperature, shown as a percentage.
Renewable Energy Certificate (REC)
A tradable record that proves one megawatt-hour of electricity was generated from a renewable source.
Request for Information (RFI)
A formal question sent during design or construction to clarify unclear or conflicting project documents.
Retail Colocation
Colocation sold in small units such as a rack or a few racks, usually to smaller customers.
Retainage
A portion of each payment to a contractor held back until the work is complete or accepted.
Rezoning
A formal change to the permitted land use category of a parcel, usually requiring a public hearing and approval by a local body.
Ride-Through
The ability of equipment to keep operating during a short power disturbance such as a sag or brief outage.
Right-of-Way
A strip of land set aside for a road, pipeline, power line or similar use.
Ring Header
A looped main pipe that can feed equipment from two directions, so a break can be isolated and flow continues the other way.
Scope 1 Emissions
Direct greenhouse gas emissions from sources an organization owns or controls, such as on-site generators burning fuel.
Scope 2 Emissions
Indirect greenhouse gas emissions from the generation of purchased electricity, steam, heating or cooling.
Scope 3 Emissions
All other indirect emissions in an organization's value chain, including construction materials, equipment manufacturing and supplier activity.
Sectionalizing Valve
A valve placed in a main pipe so one section can be isolated while the rest keeps running.
Service Level Agreement (SLA)
A contract term that sets the service a provider promises, such as uptime, and the remedies if it is missed.
Single Point of Failure
Any part whose failure stops a system that was meant to be redundant.
Single Point of Failure (SPOF)
Any component whose failure alone would stop a system from working.
Site Control
The legal right to develop a parcel, held through ownership, a lease or an option.
Software-Defined Wide Area Network (SD-WAN)
A way to manage connections between sites through software, steering traffic across multiple links.
Spine and Leaf
A network design where every leaf switch connects to every spine switch, giving predictable paths and easy scaling.
Standard Operating Procedure (SOP)
A written set of steps for performing a routine task consistently and safely.
Static Transfer Switch (STS)
A solid-state switch that moves a load between two power sources very quickly, within a fraction of a cycle, without interrupting equipment.
Strainer
A device in a pipe that catches debris so it does not damage pumps, valves or heat exchangers.
Structured Cabling
A standardized system of cables, panels and pathways that supports data connections across a facility.
Submittal
Product data, drawings or samples a contractor sends for review to show that what will be installed meets the project requirements.
Substantial Completion
The point when a project is complete enough that the owner can use it for its intended purpose, with only minor items left.
Substation
A facility that transforms and switches electrical power between voltage levels, either at the utility or on a large site.
Switchgear
Assemblies of breakers, switches and protective devices that control, protect and isolate electrical equipment.
Tax Abatement
A reduction or delay in property or other taxes granted by a government to encourage a project.
Technology Cooling System
The liquid loop closest to the servers in a liquid cooled design. It carries heat from cold plates to a coolant distribution unit.
Thermal Runaway
A condition where rising temperature causes further heat generation, a risk with some battery chemistries.
TIA-942
A telecommunications standard for data center infrastructure, covering topics like site, architecture, power, cooling and cabling, with rated levels.
Tilt-Up Construction
A building method where concrete wall panels are cast flat on the slab and then lifted into place.
Tons of Refrigeration
A unit of cooling capacity equal to 12,000 BTU per hour, or about 3.5 kW of heat removal.
Top of Rack Switch
A network switch placed in a rack that connects the servers in that rack to the wider network.
Transit
A service where one network pays another to carry its traffic to the rest of the internet.
Turnover
The formal handover of a completed facility, systems and documentation from the construction team to the owner or operator.
Uninterruptible Power Supply (UPS)
Equipment that provides short-term backup power from batteries or other storage and conditions power until generators start.
Uptime Institute Tier Classification
A rating system of Tier I to Tier IV. Tier I has basic capacity with no redundancy, Tier II adds redundant components, Tier III is concurrently maintainable, and Tier IV is fault tolerant.
Uptime Institute Tier I
The basic level, with a single path for power and cooling and no redundant components.
Uptime Institute Tier II
Adds redundant capacity components to a single distribution path, so some equipment can be removed without shutdown.
Uptime Institute Tier III
Concurrently maintainable, meaning any component can be taken out of service for maintenance without affecting IT operations.
Uptime Institute Tier IV
Fault tolerant, meaning a single failure of any component or path does not affect IT operations.
Utility Feed
The incoming electrical service from the power utility to a site. Critical facilities often have more than one feed.
Utilization
The share of available capacity, such as power, space or compute, that is actually in use.
Variable Frequency Drive
An electronic controller that changes the speed of a motor so a pump or fan can match the demand.
Variable Frequency Drive (VFD)
A controller that changes a motor's speed by varying the frequency of its power, saving energy on pumps and fans.
Virtual Power Purchase Agreement
A financial contract tied to a renewable project's output and market price. The buyer receives credits and settles price differences without taking physical power.
Water Balance
A comparison of water coming into a site with water used, evaporated, discharged and stored. A gap points to a leak or an unmetered use.
Water Consumption
Water that is taken from a source and not returned, mostly lost to evaporation.
Water Hammer
A pressure surge in a pipe caused by a sudden change in flow, such as a valve closing too fast. It can damage pipes, valves and supports.
Water Loss
Water that is bought, pumped or treated but never does useful work, such as leaks, overflows and unmetered use.
Water Meter
A device that measures how much water flows through a pipe. Ultrasonic and electromagnetic types have no moving parts.
Water Treatment
Chemical and filtration processes that control scale, corrosion and biological growth in cooling water.
Water Usage Effectiveness (WUE)
A metric of site water used per unit of IT energy, usually in liters per kilowatt-hour.
Water Withdrawal
Water taken from a source such as a river, well or utility, including water that is later returned.
Wet Bulb Temperature
The lowest temperature air can reach by evaporating water into it. It sets the limit for how cold a cooling tower can make water.
White Space
The floor area in a data center set aside for IT equipment, as opposed to mechanical and electrical rooms.
Wholesale Colocation
Colocation sold in large blocks, such as whole rooms or buildings, usually to large customers on long leases.