NewsDesksDirectoryBuildersGuidesValvesValve specs
Home / Builders / Owners, operators and end users
Directory

Owners, operators and end users

A free list of 1,884 owners, operators and end users active in data center and critical facility work in the United States and Canada. Claim your listing.

Why owners decide more than anyone else

The owner of a data center or critical facility sets the standard that everyone else on the project follows. The engineer writes the specification, the contractor buys the products and the distributor ships them, but the owner decides which manufacturers are allowed in the building. That decision usually lives in a design standard, a basis of design document, or an approved manufacturer list. If a valve maker is not on that list, it will not be bought, no matter how good the price or the lead time.

This is why data center owners and operators are the most important group in this directory. A single owner may build dozens of sites over ten years. Win a place on that owner's standard and the same valve gets specified again and again, in every new hall, every expansion and every refresh. Owners include colocation providers, hyperscale cloud companies, AI cloud builders, enterprise operators, hospitals, laboratories, chip fabs and industrial plants. They all share one trait: downtime costs far more than the price of any single valve.

Where valves sit in an owner's cooling plant

A modern data center cooling plant is mostly water and valves. Chilled water leaves the chillers and travels through large headers to air handlers, fan walls, rear door heat exchangers and coolant distribution units. Condenser water moves between the chillers and the cooling towers. In liquid cooled halls, a secondary technology loop carries a water and glycol mix from the CDU to the cold plates on the servers.

Isolation valves appear at every chiller, every pump, every tower cell, every CDU and every branch off a header. They let operators take one piece of equipment out of service while the rest keeps running. Control valves, balancing valves and check valves sit alongside them. Butterfly valves are common on pipe sizes from two inches up to the large headers because they are compact, light and cost less than gate or globe valves at those sizes. Our valve guides at /valves/ cover the selection details for each of these locations.

What owners care about when they approve a manufacturer

Owners rarely approve a valve on price alone. The questions that come up again and again are about uptime, repair and supply. Can the valve be serviced without draining the whole loop? Is the seat material compatible with the water treatment chemistry or the glycol blend? Is the valve tested to a recognized standard, such as API 598 for leak testing? Does the maker publish clear cut sheets, pressure ratings, Cv values and CAD or Revit files?

Supply matters just as much. Lead times for large valves, actuators and specialty materials have stretched on many projects. An owner who is building on a fixed schedule wants a supplier that can show real stock and a track record of shipping on time. Owners also like standardization. Using the same valve family across sites means one set of spares, one training session for the maintenance team and one set of procedures.

How a manufacturer gets onto an approved list

There is no single process, because each owner runs its own. In practice, the path has four steps. First, find out who owns the design standard. It may be a corporate engineering group, a mechanical standards lead or a procurement team. Second, learn the submission format. Many owners use a supplier portal, a request form or a spreadsheet of required documents. Third, send complete technical information: cut sheets, material lists, test reports, installation guidance and references from similar projects. Fourth, follow up through the engineers who write the project specifications, since their feedback often decides the outcome.

The best time to ask is before a project reaches the bidding stage. Once the specification is final, changes are slow and costly. When a design is still open, owners and engineers are far more willing to look at a new option. Our valve spec kit at /butterfly-valve-specs.html gives engineers copy and paste specification language, pressure ratings and Cv data that can speed that review.

What to prepare before you contact an owner

Keep the first contact short and specific. Say which loops and pipe sizes you can serve, which standards the products meet, and where documents can be found without a login. Mention real stock and lead time information only if it is accurate and current. Have a one page summary ready, plus links to the full cut sheets. Avoid sending large attachments to people you have not spoken with, since many companies filter them.

It also helps to read the owner's public information first. Look at recent project announcements, sustainability reports and technical presentations. These often name the cooling approach a company favors, such as air cooled chillers, water cooled plants, direct to chip liquid cooling or immersion. Matching your message to that approach shows you did your homework.

Standardization, spares and total cost

Owners think in total cost of ownership, not purchase price. A valve that costs a little more but lasts longer, seals better and needs fewer spare parts can cost less over twenty years. Standardizing on a small number of valve families across a portfolio reduces the number of spare parts on the shelf, shortens training and lets operators move between sites without relearning equipment.

Maintenance planning also drives choices. Owners ask how a seat is replaced, whether a stem can be serviced in the line and how long a repair takes. They compare actuator options, manual override and position indication. Clear maintenance documents are part of the approval, not an extra.

Trends that are changing owner requirements

Three trends are reshaping what owners ask for. First, rack power is rising fast with AI workloads, which pushes more owners toward direct liquid cooling and larger chilled water plants. Second, water use is under scrutiny, so owners look at closed loop designs, higher supply temperatures and waterside economizers. Third, build speed matters more than ever, so prefabrication, stocked products and dependable supply have become selection criteria.

Each trend changes the valve picture. Liquid cooling adds technology loops with water and glycol and tighter leak expectations. Higher operating temperatures change material choices. Faster schedules put pressure on lead times. Suppliers who understand these shifts speak the owner's language.

Frequently asked questions

What is an approved manufacturer list?

It is a list kept by an owner or engineer of the manufacturers whose products are allowed on a project. Products from makers not on the list generally need a formal review before they can be used.

Who decides which valves go into a data center?

The owner sets the standard, the design engineer writes the specification, and the mechanical contractor buys and installs the valves. All three have a say, but the owner's standard usually has the final word.

Can a company be listed for free?

Yes. Use the Claim or add a company form. We review each submission before it is published.

How to use this list

The list below shows owners, operators and end users that appear in data center and critical facility project information for the United States and Canada. Use the search box to find a company, then use the Look up link to find its website and the people who handle engineering and procurement. If you work for one of these companies and want to correct your listing, add a website or send a logo, use the Claim link. Listings are free, and every submission is reviewed before it goes live.

The list

Missing or wrong?
Listings come from public project information. Claim yours to correct it, add a website or send your logo.