Data Center Outreach / Valve Kit Pick a valve Pressure Cv data Series data Materials Where they go Get specified Guide spec Revit & CAD Contact
Data centers · Chillers · Condenser water · Liquid cooling · Critical facilities

Valve data you can paste straight into your plans

Pratt Industrial butterfly valves, laid out for the people drawing and specifying the job. Sizes, pressures, materials, Cv, model strings, a Division 23 guide spec and a basis of design paragraph. One click copies each one. Nothing to sign up for.

Compare the three series
1"–72"Combined size range across OS, BF and HP
150–1440psi, from ANSI 125/150 up to Class 600
API 609Design standard on all three series
API 598Every valve leak tested at rated pressure

Pick a valve in 30 seconds

Almost every butterfly valve on a cooling loop is one of two designs. Resilient seated valves (BF and OS) seat into an elastomer ring. High performance double offset valves (HP) seat into a fluoropolymer seat set back behind the shaft. Start with the flange class and size of the line.

SeriesDesignSizesPressureBodyGood fit for
BFResilient seated, wafer or lug2"–24"250 psi (2"–12"), 150 psi (14"–24")Ductile ironChilled water and condenser water isolation at ANSI 125/150 flanges
OSResilient seated, wafer or lug1"–48"200 psi (1"–12"), 150 psi (14"–48")Ductile ironThe widest size range for mechanical rooms and large headers at ANSI 125/150 flanges
HPHigh performance double offset2"–72"Class 150: 285 psi · Class 300: 740 psi · Class 600: 1440 psiWCB carbon steel or CF8M stainlessCDU and technology cooling loops, glycol service, higher pressure classes, modulating duty

Pressure at a glance

Every rating on one scale, 0 to 1500 psi. Blue is resilient seated (BF and OS). Orange is high performance (HP). Then check your own line below.

Resilient seated · BF and OS

High performance double offset · HP

Flow capacity by size

Cv at full open for the size you pick. Higher Cv means less pressure drop across the valve.

Cv at full open

Full tables by degree of opening, 10° through 90°, are in each brochure. If a valve will do any control work, size against Cv at the position it will actually sit, not the full open number. A 12" BF at 60° open is 2,799 against 9,245 wide open, roughly 30% of full capacity.

SizeBFOSHP Cl 150HP Cl 300HP Cl 600
2"206.41158888—
4"825.6600410410243
6"1,8581,5791,060995630
8"3,3023,1362,2001,9001,100
12"9,2458,2504,7004,1002,700
16"16,43516,3887,9006,9005,100
20"25,68027,90813,80012,6007,800
24"36,97943,11621,10018,90012,500

Series data, ready to copy

Each card has the facts engineers ask for first. The schedule row pastes as tab separated columns into a Revit valve schedule or a spreadsheet.

BF Series

Resilient seated · wafer BF1 / lug BF2 · API 609 Cat. A

A thin, high-flow disc on a two-piece shaft with full-length bushings. A three-point tongue-and-groove seat holds under high dead-end pressure and full vacuum.

Sizes
2" to 24"
Pressure
250 psi 2"–12" · 150 psi 14"–24"
Body
One piece ductile iron ASTM A536 65-45-12
Disc
Ductile iron with ENP plating or nylon 11, CF8M stainless, or aluminum bronze
Shaft
Heat treated 416 stainless, two shafts, blowout proof
Seat
EPDM, Buna-N or Viton, field replaceable
Bushings
Two full length Nylatron
Flanges
Wafer: ANSI 125/150, PN10, PN16 · Lug: ANSI 125/150 · B16.1 / B16.5 · ISO 5752
Model string
BF1-0208688 = wafer, 2", ductile iron body, CF8M disc, 416 stem, EPDM seat
Series page Brochure (PDF)

OS Series

Resilient seated · wafer OS1 / lug OS2 / flanged OS3 · API 609 Cat. A

The same tongue-and-groove seat design as the BF, in the widest size range of the three. Three upper bushings and one lower bushing reduce stem friction and torque.

Sizes
1" to 48"
Pressure
200 psi 1"–12" · 150 psi 14"–48" · Viton rated 165 psi
Body
One piece ductile iron ASTM A536 65-45-12
Disc
Ductile iron with ENP plating or nylon, 304 stainless, or aluminum bronze
Shaft
Heat treated 410 stainless, two shafts
Seat
EPDM, Buna-N or Viton, field replaceable
Bushings
Three upper and one lower RTFE
Shaft seal
Self-adjusting O-ring, pressure or vacuum service
Model string
OS1-020-8CF8 = model, size, then body, disc, stem and seat codes
Series page

HP Series

Double offset · API 609 Cat. B · API 607 fire-safe

A double offset disc with a spherical sealing surface and a free-floating, pressure-assisted seat. Fluoropolymer seat options, higher pressure classes, and sizes up to 72".

Sizes
2" to 72"
Pressure
Class 150: 285 psi (2"–72") · Class 300: 740 psi (2"–48") · Class 600: 1440 psi (3"–24")
Body
WCB (A216) carbon steel or CF8M (A351) stainless. Other alloys on request
Disc
CF8M (A351) stainless
Shaft
Hardened 17-4 PH stainless, one piece, blowout proof
Seat
PTFE, RTFE or MTFE standard, with 316 stainless, Inconel, metal and fire-safe options
Body styles
HP1 wafer · HP2 lug · HP3 short flanged · HP4 long flanged · HP5 butt-weld
Standards
ASME B16.34, API 607, API 598 (100% tested), MSS SP-68, ASME B16.10, ISO 5752, BS 5155
Extras
Gland packing below the bonnet so automation direct mounts, 2" minimum neck clearance for insulation, integral travel stop. Test reports and MTRs on request
Series page Brochure (PDF)

Materials and stainless options

Ductile iron and carbon steel are standard. Stainless is available on every series, so say it in the spec when the service calls for it. Stainless parts also change the pressure rating on some builds, so confirm with the manufacturer.

SeriesBodyDiscStainless options
BFDuctile iron A536 65-45-12Ductile iron ENP or nylon 11, CF8M stainless, aluminum bronzeCF8M stainless disc. Heat treated 416 stainless shaftBF data
OSDuctile iron A536 65-45-12Ductile iron ENP or nylon, 304 stainless, aluminum bronze304 stainless disc. Heat treated 410 stainless shaftOS data
HPWCB carbon steel (A216) or CF8M stainless (A351)CF8M stainlessCF8M stainless body and disc, 17-4 PH stainless shaft, 316 stainless or Inconel seat options. Other alloys on request, including Alloy 20, Hastelloy C276, Monel and Duplex 2205HP data

What they look like

Watch each valve open and close. The first two drawings look down the shaft. Closed, the disc blocks the pipe. Open, it turns to lie along the flow. The last two look down the pipe at the body styles. Product photos for every series are on the manufacturer series pages.

CLOSEDOPEN BF and OS

Resilient seated. The disc presses into an elastomer ring (EPDM, Buna-N or Viton) in the body.

CLOSEDOPEN HP

Double offset. The shaft sits behind the disc, so the disc lifts away from the seat as it opens, and drags less. PTFE, RTFE, MTFE or metal seat.

Wafer

Sits between two flanges. Lightest and most compact. Not for dead-end service.

Lug

Tapped bolt holes. Each flange bolts to the valve on its own, so it suits dead-end service.

Where the valves go in a cooling plant

A data center is a water plant with servers in it. A butterfly valve on a chilled water loop gets chosen during design, bought during construction, and stays where it is for as long as the building runs. Isolation and control points show up through every loop below. Final locations are always per system design.

LoopTypical serviceWhat matters
Chilled water, closedIsolation at chillers, pumps, air handlers and headers. Balancing and control with actuationElastomer selection against treatment chemistry. Full vacuum rating
Condenser water, openIsolation at towers, condensers and pumps. Basin and bypassOpen loop chemistry. Lug body where dead end service is required
CDU and technology coolingIsolation and control on liquid cooling distribution, water-glycolFluoropolymer seat options. Higher pressure classes available
Waterside economizerChangeover and isolationOperating pressure and cycling frequency drive the choice
Makeup and facility waterIsolation on makeup, fill and drainStandard trim per site water quality

What a cut sheet does not tell you

The questions that come up most once a valve is on the drawing.

Disc projection beyond the body face

The disc swings past the face of the valve as it opens. Check the ØA and ØB dimensions against the pipe ID before committing a layout, especially next to a reducer, a fitting or lined pipe.

Weight, for supports and hangers

A 24" BF lug is roughly 408 lbs bare. A 24" HP Class 300 lug is roughly 1,005 lbs and Class 600 roughly 2,110 lbs. Add the actuator on top.

Insulation clearance

HP carries an extended neck with a minimum 2" bonnet to flange clearance on all sizes. On BF and OS, check the E dimension against your insulation thickness.

Actuator mounting

All three series use an ISO 5211 top flange. BF also carries Kv industrial drilling and HP offers ISO drilling on request.

Getting the part number right

If a specific disc or seat material needs to arrive, it has to be in the model string. Each brochure has the ordering table.

Three questions to settle early

1. Which positions modulate rather than isolate. 2. What is the actual fluid, since glycol percentage and water treatment drive elastomer selection and EPDM, Buna-N and Viton are not interchangeable. 3. Where dead end service is required, since a wafer body has no mechanical attachment to either flange and HP vacuum-rated dead end service is lug type only.

Five steps to a listed manufacturer

  1. Name a basis of designPaste the paragraph from the guide spec into Section 23 05 23 while the mechanical spec is open.
  2. Add to the approved listPut the manufacturer on the owner's approved manufacturer list or master spec so every project inherits it.
  3. Attach the submittal dataCut sheets, Cv tables, dimensional data and suggested spec language are published for every series.
  4. Confirm stock and lead timeAsk before the bid, not after. Use the request template in the stock tab.
  5. Name a local distributorDistributors stock and ship across the country. Ask for the nearest one.

What a company needs for its approved list

Requirements vary by owner and engineer. Most ask for the items below. A manufacturer name and location is enough to start. A person's name and a street address are not required to name a basis of design.

  • Manufacturer name and location
  • Product lines and model strings
  • Design and test standards (API 609, API 598)
  • Cut sheets and suggested specification language
  • Cv data by degree of opening
  • Dimensional data for wafer and lug
  • Material test reports and test certificates (HP, on request)
  • Distributor or local contact
  • Company forms such as insurance, safety and tax, through supplier registration on request
Manufacturer information, ready to paste
MANUFACTURER INFORMATION FOR APPROVED MANUFACTURER LIST

Manufacturer: Pratt Industrial
Location: Emporia, Kansas. Manufacturing, warehouse and full-service machine shop, over 65,000 sq ft
Customer service: 1.800.423.1323
Web: prattindl.com
Products: Butterfly valves. BF Series (2 to 24 in), OS Series (1 to 48 in), HP Series double offset (2 to 72 in)
Pressure: BF 250 psi (2-12 in) and 150 psi (14-24 in). OS 200 psi (1-12 in) and 150 psi (14-48 in). HP Class 150, 300 and 600
Standards: API 609, API 598, ISO 5211, ASME B16.1 / B16.5. HP also ASME B16.34 and API 607
Actuation: Lever, worm gear, pneumatic, electric
Documents available: Cut sheets, suggested specification language, Cv tables, dimensional data, CAD files. Material test reports and test certificates on request (HP)
Submittal package requests: info@datacenteroutreach.com

The paragraph to paste

Naming a basis of design early keeps the submittal, the schedule and the replacement parts simple. These blocks are written to drop into a project specification. Edit them to fit your project.

Basis of design paragraph
BASIS OF DESIGN: Butterfly valves for chilled water, condenser water and liquid cooling loops shall be Pratt Industrial, Emporia, Kansas. Series BF or OS (wafer or lug) for ANSI 125/150 flanged piping, and Series HP (double offset) for ANSI Class 150, 300 and 600 piping as required by pressure and service. Equivalent products by other manufacturers may be submitted for approval by the Engineer.
Approved manufacturer list line
Manufacturer: Pratt Industrial
Product: Butterfly valves, BF, OS and HP Series
Sizes: 1 to 72 inches
Standards: API 609, API 598, ISO 5211, ASME B16.1 / B16.5
Location: Emporia, Kansas (manufacturing, warehouse and machine shop)
Web: prattindl.com
Customer service: 1.800.423.1323
Division 23 guide spec
SECTION 23 05 23 - BUTTERFLY VALVES FOR HVAC AND CRITICAL COOLING PIPING

PART 1 - GENERAL
1.1 SUMMARY
  A. Section includes resilient seated and double offset butterfly valves for chilled water, condenser water, glycol and liquid cooling piping.
1.2 REFERENCES
  A. API 609, Butterfly Valves: Double-flanged, Lug- and Wafer-type.
  B. API 598, Valve Inspection and Testing.
  C. API 607, Fire Test for Quarter-turn Valves (HP Series with fire-safe seat).
  D. ASME B16.1 and B16.5, Flanges. ASME B16.34, Valves.
  E. ISO 5211, Actuator Attachment. ISO 5752, Face-to-Face Dimensions.
1.3 SUBMITTALS
  A. Product data, dimensions, materials of construction, pressure ratings and Cv data.
  B. Actuator and accessory data where valves are automated.
1.4 QUALITY ASSURANCE
  A. Each valve shall be leak tested in the factory at its rated pressure per API 598.

PART 2 - PRODUCTS
2.1 MANUFACTURER
  A. Pratt Industrial, Emporia, Kansas, or approved equal.
2.2 WAFER AND LUG BUTTERFLY VALVES, 1 TO 48 INCHES (BF, OS)
  A. Service: Lug valves shall be designed for installation between ANSI 125/150 flanges. Wafer valves shall be designed for installation between ANSI 125/150 flanges [and PN 10 and PN 16 flanges (BF)]. All valves shall be capable of bi-directional, end of line, bubble tight service to rated pressure and shall be rated to full vacuum service. Design standard: API 609 Category A.
  B. Pressure rating: [BF: 250 psi 2 to 12 inches, 150 psi 14 to 24 inches] [OS: 200 psi 1 to 12 inches, 150 psi 14 to 48 inches].
  C. Body: One piece ductile iron, ASTM A536 Grade 65-45-12, laying length per ISO 5752, flange connection per ASME B16.1/B16.5.
  D. Disc: Ductile iron ASTM A536 Grade 65-45-12 with ENP plating [or nylon 11 coating] [CF8M stainless steel (BF)] [304 stainless steel (OS)] [aluminum bronze]. Disc shall accommodate an upper and lower shaft with a thin center profile giving higher Cv values combined with strength.
  E. Shaft: [Heat treated 416 stainless steel (BF)] [Heat treated 410 stainless steel (OS)]. Two shafts, upper and lower. The upper shaft shall have positive engagement in the disc through an internal square drive and be retained by the body top cap. Shaft shall be blowout proof per API 609 with a secondary stem journal seal preventing leakage to atmosphere.
  F. Seat: [EPDM] [Buna-N] [Viton], field replaceable. Seat shall have three tongues (two on the side walls and one in the center bore) engaging three grooves in the body to prevent seat movement in a radial and axial direction.
  G. Shaft seals: Upper shaft seal shall be [self-adjusting V-type (BF)] [self-adjusting O-ring (OS)], suitable for pressure or vacuum service. Bottom end cap shall contain a captive O-ring creating a positive seal against external leakage.
  H. Bushings: [Two full length Nylatron bushings, upper and lower (BF)] [Three upper and one lower RTFE bushing (OS)].
  I. Top flange: ISO 5211 for direct actuator mounting.
  J. Lug style valves shall be suitable for dead-end service.
  K. Operators: [Lever] [Worm gear] [Pneumatic actuator] [Electric actuator].
2.3 DOUBLE OFFSET BUTTERFLY VALVES, 2 TO 72 INCHES (HP)
  A. Design: Double offset disc and shaft with a spherical sealing surface and a free-floating, pressure-assisted seat retained between the body and a retention ring. Bi-directional sealing with soft seat. API 609 Category B.
  B. Pressure class: [ASME Class 150, 285 psi, 2 to 72 inches] [Class 300, 740 psi, 2 to 48 inches] [Class 600, 1440 psi, 3 to 24 inches], suitable for installation between ASME B16.5 flanges.
  C. Body: [WCB carbon steel ASTM A216] [CF8M stainless steel ASTM A351]. Styles: [wafer] [lug] [short flanged] [long flanged] [butt-weld].
  D. Disc: CF8M stainless steel ASTM A351. Shaft: One piece hardened 17-4 PH stainless steel, blowout proof.
  E. Seat: [PTFE] [RTFE] [MTFE] [316 stainless steel] [Inconel] [Fire-safe, tested to API 607].
  F. Bearings: Full length upper and lower, 316 stainless steel impregnated with [PTFE] [graphite].
  G. Packing: [Multi-layer PTFE cup and cone] [Die-formed graphite for metal seated and fire-safe valves], located below the bonnet for direct mounting of automation.
  H. Integrally cast travel stop and extended neck with a minimum 2 inch bonnet to flange clearance for insulation.
  I. Vacuum rated dead end and double dead end service: lug type only.
  J. Material test reports and test certificates available on request.

PART 3 - EXECUTION
3.1 INSTALLATION
  A. Install valves with the disc partly open during flange bolting to protect the seat.
  B. Use the flange gasket and bolting recommended by the piping specification. Do not install additional gaskets on resilient seated valves.
  C. Verify disc swing clearance against the pipe inside diameter, reducers and fittings before installation.
  D. Support valves and actuators independently where weight requires.
3.2 FIELD QUALITY CONTROL
  A. Operate each valve fully open and closed to verify smooth travel and position indication before system flushing.
  B. Leak test with the piping system per Section 23 21 13.

END OF SECTION 23 05 23

Revit, CAD and cut sheets

Brochures and series pages are public on the manufacturer site. CAD files are sent on request so you always get the current version. Revit families are in progress.

CAD drawings

2D and 3D drawings for the series on this page, with dimensions and actuator mounting data.

info@datacenteroutreach.com

Revit families

In progress for BF, OS and HP. Ask to be sent the families when they are released.

info@datacenteroutreach.com

Cut sheets

Brochures with materials, dimensions, Cv tables and suggested specification language, straight from the manufacturer.

Ask a sizing question

Flow, pressure drop, dead-end service or actuator sizing on a live job. Send the line size, flange class and service.

Ask for data, files or a stock check

Tell us what you are working on. We reply by email at info@datacenteroutreach.com.

Copied